photo

Manikandan


anna university

Last seen: 2 maanden ago |  Active since 2012

Followers: 0   Following: 0

Message

Professional Interests: Electric Drives

Statistics

All
  • Explorer
  • Personal Best Downloads Level 1
  • First Review
  • 5-Star Galaxy Level 2
  • First Submission
  • Revival Level 3
  • First Answer

View badges

Feeds

View by

Answered
PI control techniques for speed control of a BLDC motor
Try to use trial and error method

meer dan 6 jaar ago | 0

Answered
How to change Simulink model line widths
Don't take screen shoot. Go to edit, then copy model to clipboard. after past it as picture in your word. hence the quality of p...

meer dan 8 jaar ago | 3

Submitted


Measure the Frequency of given input Square wave
Contact: electricmani@yahoo.co.in

bijna 9 jaar ago | 1 download |

Thumbnail

Answered
how to control the position of a DC motor by FLC
i completed the same, refer this link, if you want more clarification write me: electricmani@yahoo.co.in http://ieeexplore.ie...

bijna 9 jaar ago | 0

Answered
Why is the induction motor speed very low and at a negative value
set your scope parameter setting, uncheck limited data points. reduce torque as zero.

bijna 9 jaar ago | 0

Answered
How to control a brushless motor through a ESC with C2000 using "Embedded Coder" Library in Simulink
I did same like, write me: electricmani@yahoo.co.in

bijna 9 jaar ago | 0

Answered
i am unable to get proper operations at 10 KHz speed of the "Repeating Sequence" block of Simulink under SimPowerSystems/Control& Measurements Library. With time values [0 1e-4 1e-4] for values [0 1e-4 0] the output is zero when run for 1 sec.
For 10khz output, use time value: (0 (1/10e3) and amplitude value: (0 1), then use less sampling time in solver, typically 2e-6 ...

bijna 9 jaar ago | 0

Answered
Is this the proper way to implement PID for 3 Phase inverter induction motor speed control?
Lot of theoretical methods available to find KP, Ki and Kd values, my suggestion for beginner try to do trial and error method. ...

bijna 9 jaar ago | 0

Answered
speed control of dc motor using SMC
First start open loop control of motor, verify with closed loop conventional PID controller, then change into SMC.

bijna 9 jaar ago | 0

Answered
Use PWM to control Speed of brushless dc motor!
use AND gate instead of product block. for more details contact me: electricmani@yahoo.co.in

ongeveer 9 jaar ago | 1

Answered
how to find the setpoint ref input block in simlink for design of PI controller to control speed of servo motor... i can't find the setpoint bock in simulink.... setpoint ref input block...
use constant block

ongeveer 9 jaar ago | 2

Answered
i want to control speed of DC motor using arduino via matlab.
use PWM

ongeveer 9 jaar ago | 0

Answered
Single phaseInduction motor speed control
Your problem?

ongeveer 9 jaar ago | 0

Answered
how to do simulation of speed control of three phase induction motor by v/f method
Contact me: electricmani@yahoo.co.in

ongeveer 9 jaar ago | 1

Answered
How to implement speed control of induction motor using Fuzzy logic
Contact me: electricmani@yahoo.co.in

ongeveer 9 jaar ago | 0

Answered
How to specify time values and Output values for sawtooth waveform?
Time: [0 2.5000e-005] Output: [0 1]

ongeveer 9 jaar ago | 0

Answered
Tuning a pid controller. sampling times must agree?
Motor modeled as mathematical or taken from simpower system tool.

ongeveer 9 jaar ago | 0

Answered
Fixed Step Solver Problems
Reduce your sample time as much as possible to small.

ongeveer 9 jaar ago | 0

Answered
calculation of time difference between two crossings of voltage waveforms in simulink
Refer my paper: http://www.ripublication.com/ijaer_spl/ijaerv10n10_59.pdf

ongeveer 9 jaar ago | 0

Answered
How to determine the controller parameters for BLDC drive?
Refer slandered control system books for ZN method.

ongeveer 9 jaar ago | 0

Answered
torque ripple minimisation for bldc motor using direct torue control and indirect flux control
you need to mathematical modeling of motor.

ongeveer 9 jaar ago | 1

Answered
there is a built in model of brushless DC motor in simulink library. does anyone know the equations used for built in model of BLDC.
like it.

ongeveer 9 jaar ago | 0

Answered
Hi, i want to build an bldc motor in motor in matlab , i dont want to use an inbuilt motor block present in simulink .
I tried mathematical modeling of BLDC, but its result differ from simulik library BLDC motor. anybody have clear idea, post here...

ongeveer 9 jaar ago | 0

Answered
Servo motor controlling using MATLAB
Yes possible, but you need MATLAB supported hardware. what's your platform wish to work.

ongeveer 9 jaar ago | 0

Answered
Ball Screw driven XY table using AC servo motor.
Contact me @ electricmani@yahoo.co.in

ongeveer 9 jaar ago | 0

Answered
how to calculate parameters for dc servo motor simulation?
you should contact manufacture or google it to find required data's. not possible to find required data from the available data....

ongeveer 9 jaar ago | 0

Answered
Control Servo Motor
use analog output from the real time windows target tool box and select your DAQ via USB. then generate analog output voltage to...

ongeveer 9 jaar ago | 0

Answered
Tacho feedback in a servo
If you use simulink for DC motor position control, use motor output speed wm in rad/sec from measurement block. convert equivale...

ongeveer 9 jaar ago | 0

Answered
In which location ,we have to store the .fis file?
We need to import the file from work space or call where it was stored, before need to export designed fis to work space. me too...

ongeveer 9 jaar ago | 0

Answered
quadrature/rotary encoder .mdl file
I did the same things, if need help contact me on electricmani@yahoo.co.in

ongeveer 9 jaar ago | 0

Load more