photo

Pranav Murali

MathWorks

Last seen: ongeveer 4 jaar ago Active since 2020

Followers: 0   Following: 0

I'm an Application Support Engineer of Mathworks. My primary area of interest is Embedded Systems. On the whole, I'm comfortable with anything related to electronics.

DISCLAIMER: All my comments are personal opinion only and do not represent or voice MathWorks in any way.

Statistics

  • Knowledgeable Level 2
  • Revival Level 2
  • First Answer

View badges

Feeds

View by

Answered
SOC estimation using UKF
I can understand that you are interested in knowing how we arrived at the values of Em, R and C stored in the lookup table. In t...

ongeveer 4 jaar ago | 1

| accepted

Answered
How to read SparkFun 9DoF Razor IMU into MATLAB?
I understand that you tried to deploy your code on SparkFun Razor with the Zero firmware. I am not quite sure if there are any p...

ongeveer 4 jaar ago | 0

| accepted

Answered
UWB - data transmission - signal processing
I understand that you are looking to transmit a binary pulse over UWB. Please follow the references given below: UWB Monocycle....

ongeveer 4 jaar ago | 0

Answered
Where can I find the "SoC estimation using kalman fiter block" ?
The Kalman filter blocks used to estimate SoC of a battery can be found in the Control System Toolbox.

ongeveer 4 jaar ago | 0

Answered
Equivalent Circuit Battery Block: Battery.PulseSequence
I see that you are interested in knowing the parameters and values stored within the pulse sequence. The command Battery.PulseSe...

ongeveer 4 jaar ago | 0

| accepted

Answered
Simulink - Send and receive float over serial port
I can understand that you are trying to send some data through a serial port which however is getting lost after transmission. I...

ongeveer 4 jaar ago | 0

Answered
Getting waveform by using UART on Raspberry Pi and ADC on Ti F28335
I see that your waveforms from the ADC aren’t similar as they are supposed to. Since they sampling frequencies are different, If...

ongeveer 4 jaar ago | 0

Answered
IMU/INS sensor fusion with Cartesian coordinates
Currently, the Intertial Sensor Fusion functions only support geodectic coordinates as ReferenceLocation. So, the cartesian envi...

ongeveer 4 jaar ago | 0

| accepted

Answered
Read rotary encoder from Arduino Uno in Simulink
I understand that you are trying to read the counts from a rotary encoder using Simulink. Although Simulink doesn't have a block...

ongeveer 4 jaar ago | 0

| accepted

Answered
Why the output of the Switch block is not a bus ?
Hi Prem, I understand that both the inputs of your switch are bus signals but the output in not a bus signal. Please check the ...

ongeveer 4 jaar ago | 0

Answered
How to improve ROS subscriber and publisher rate in Simulink
Hi Zi, I see that you are creating three publisher-subscriber pairs on ROS and they take more time to process than the desired ...

ongeveer 4 jaar ago | 0

Answered
RGB LED control help
Hi Madison, I understand that you are trying to control a digital RGB led strip based on the input from switches using the Ardu...

meer dan 4 jaar ago | 0

Answered
Parrot Minidrone - stable flight
Hi Keith, It’s a nice idea to use the optical flow values for a good, controlled flight. Here’s a couple of things you can try:...

meer dan 4 jaar ago | 0

| accepted

Answered
How do I apply constraints to state space response of a continuous time system?
Hi Kedar, Your state space model should be designed appropriately to provide responses within your desired range.

meer dan 4 jaar ago | 0

Answered
Plotting a relation from a describing equation - optimized trapezoidal steering optimization
Hi Igor, I see that you’ve been trying to visualize the difference between optimized trapezoidal and Ackerman steering. Finding...

meer dan 4 jaar ago | 0

Answered
Calculating time of flight from a series of acoustic waveforms
Hi Lorenzo, You are trying to calculate the time of flight from the dataset you have. The transmitted and received signal (Volt...

meer dan 4 jaar ago | 1

| accepted

Answered
Trouble writing PWM signal from PID controller
Hi Chris, I understand that you are receiving the correct value of PID but you are unable to control the output duty cycle of y...

meer dan 4 jaar ago | 1