Danikha Shyken
Followers: 0 Following: 0
Statistics
29 Questions
0 Answers
RANK
225.390
of 294.407
REPUTATION
0
CONTRIBUTIONS
29 Questions
0 Answers
ANSWER ACCEPTANCE
68.97%
VOTES RECEIVED
0
RANK
of 20.109
REPUTATION
N/A
AVERAGE RATING
0.00
CONTRIBUTIONS
0 Files
DOWNLOADS
0
ALL TIME DOWNLOADS
0
RANK
of 151.611
CONTRIBUTIONS
0 Problems
0 Solutions
SCORE
0
NUMBER OF BADGES
0
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Feeds
Question
Hello. If I have included delays in my code for my controller, how do I implement it so that the delays are considered when the code is executed?
this is the simulink model where the buck-boost controller is connected to the gate ports of each switch to power up the conve...
10 maanden ago | 1 answer | 0
1
answerQuestion
Hi. How do I maintain the square wave output of the 1-D?
the blue triangular waveform is the waveform of 1-D, and the red square wave is the D
10 maanden ago | 1 answer | 0
1
answerQuestion
Hi. In Simulink modeling, what can we do to ensure that the switching waveforms of the duty cycle and 1-duty cycle are not in phase?
q1 is the duty cycle (D), and q3 is the 1-duty cycle (1-D)
10 maanden ago | 2 answers | 0
2
answersQuestion
Hello. Could someone please suggest other components or blocks I can use to avoid using the step input block for the duty cycle?
Because I need the amplitude to reach 1.8V, and I only get 1V with the step input.
10 maanden ago | 1 answer | 0
1
answerQuestion
Could someone please assist me? My code for the buck-boost converter controller isn't working properly when I run it.
this is the Simulink model
12 maanden ago | 1 answer | 0
1
answerQuestion
Hello, if you have a moment, I could use your help in resolving this error.
12 maanden ago | 2 answers | 0
2
answersQuestion
Greetings, if you have a moment, I could use your help in resolving this error.
12 maanden ago | 1 answer | 0
1
answerQuestion
Hello, how do I feed the output of the input selector to the buck-boost converter using Simulink modeling?
12 maanden ago | 1 answer | 0
1
answerQuestion
Hey there, I need some help with this error. Would anyone be willing to provide guidance?
How do I reduce the fixed step size or tighten the error tolerances?
12 maanden ago | 1 answer | 0
1
answerQuestion
Hi there, I'm encountering an issue and would appreciate your guidance in resolving it.
12 maanden ago | 1 answer | 0
1
answerQuestion
Greetings! I'm looking for assistance in understanding what's causing the problem in my code.
this is the MATLAB code: function y = determineMode(teg, pv, pzt, ~, D, ~, ~, ~, ~) % Inputs: % teg: Voltage from T...
ongeveer een jaar ago | 1 answer | 0
1
answerQuestion
Hey there, I need some help with this error. Your guidance would be valuable.
ongeveer een jaar ago | 0 answers | 0
0
answers1
answerQuestion
Hi, would someone be willing to assist me in resolving this error
ongeveer een jaar ago | 1 answer | 0
1
answerQuestion
hey, could somebody please help me understand and resolve this error?
ongeveer een jaar ago | 1 answer | 0
1
answerQuestion
hello, can somebody help me figure out how to improve this Simulink model so that it has four output ports instead of a single output port?
ongeveer een jaar ago | 1 answer | 0
1
answerQuestion
hi, is the simulink model shown below possible?
we feed 4 input switches into a stateflow
ongeveer een jaar ago | 0 answers | 0
0
answersQuestion
Hello, can someone please help me understand this error?
I'm particularly confused about the part which says '... and the phase delay parameters of this block need to be integer multi...
ongeveer een jaar ago | 1 answer | 0
1
answer1
answerQuestion
Hello, could someone kindly assist me in resolving this error?
ongeveer een jaar ago | 1 answer | 0
1
answerQuestion
Can someone please help me learn how to make automatic switching based on available voltage sources to power up a three-input buck-boost converter?
An example of this operation would be: TEG: 0.3 - 0.4V PV: 0.4 - 1.2V PZT: 1.2 - 2V Ideal Output: 1.8V If the available...
ongeveer een jaar ago | 1 answer | 0
1
answerQuestion
Hi. Could someone please assist me in resolving this issue?
ongeveer een jaar ago | 1 answer | 0
1
answerQuestion
Could someone please tell me which components are missing for this circuit to automatically and appropriately select inputs when dealing with multiple inputs?
3 inputs
ongeveer een jaar ago | 1 answer | 0
1
answerQuestion
Hi! I need some help. I'm confused as to why this selection mode circuit I modified won't work properly with three inputs.
1st input: 0.3 - 0.4V 2nd input: 0.4 - 1.2V 3rd input: 1.2 - 2V
ongeveer een jaar ago | 1 answer | 0
1
answerQuestion
Hello! Could someone kindly assist me in comprehending the purpose and operation of the system shown below?
This is one of the subsystems of an input selector circuit.
ongeveer een jaar ago | 1 answer | 0
1
answerQuestion
Hi! Could someone please provide me with an idea of how to model a selector for multiple inputs using Simulink? Thank you.
Input sources: Thermoelectric Generator(TEG), Photovoltaic(PV), and Piezoelectric(PZT)
ongeveer een jaar ago | 1 answer | 0
1
answerQuestion
What should be the inductor initial current and capacitor initial voltage with an input range of 0.02-0.16V
for a two MOS switch two diodes buck-boost converter with an input of 0.02V, resistor load of 2,142,857.143 Ω, inductance of 1 m...
meer dan een jaar ago | 1 answer | 0
1
answerQuestion
What should be the initial value of the inductor and capacitor with an input range of 0.02-0.16V
For a two MOS switch two diodes buck-boost converter with an input of 0.02V, resistor load of 2,142,857.143 Ω, inductance of 1 m...
meer dan een jaar ago | 0 answers | 0