Statistics
RANK
839
of 297.016
REPUTATION
90
CONTRIBUTIONS
0 Questions
68 Answers
ANSWER ACCEPTANCE
0.00%
VOTES RECEIVED
11
RANK
of 20.419
REPUTATION
N/A
AVERAGE RATING
0.00
CONTRIBUTIONS
0 Files
DOWNLOADS
0
ALL TIME DOWNLOADS
0
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Feeds
Simscape Tank (G-TL) Elevation from a reference
The best way may be to use the Pipe (TL) block in Simscape Fluids. Closed conduit that transports fluid between thermal liquid ...
meer dan een jaar ago | 0
Why are my simulink initial conditions sometimes not met, despite high priority?
When selecting Start simulation from steady state, the solver tries to find what the model would go to after a very long simulat...
meer dan een jaar ago | 0
How can I model an Elbow in Simspace while using the TL library?
Elbows are available in the Thermal Liquid library in Simscape Fluids as of R2022a. Pipe turn in a thermal liquid network - MAT...
meer dan een jaar ago | 0
Interface (TL-IL) variable temperature
Thermal liquid elbows have been added as of R2022a. Pipe turn in a thermal liquid network - MATLAB (mathworks.com)
meer dan een jaar ago | 0
Simulate interface between a Thermal Liquid and Two-Phase Fluid
Models heat exchange between a thermal liquid network and a network that can undergo phase change - MATLAB (mathworks.com) A mo...
meer dan een jaar ago | 0
how do I use run-time parameter with simscape gas-charged accumulator
I know that this is an older question. As of a few years ago, all parameters in the Gas-charged Accumulator are run-time capable...
meer dan een jaar ago | 0
How to access to two-phase fluid properties during run
This might be the block that you need: Measure temperature, density, specific enthalpy, specific entropy, and specific volume in...
meer dan een jaar ago | 0
How can I simulate jamming fault at a certain time?
One possibility would be to use the Rotational Damper in Simscape Driveline: Linear rotational damper - MATLAB (mathworks.com) ...
meer dan een jaar ago | 0
Simulink Model DC Motor with Transmission Gear
Please see Vehicle in Simscape Driveline and Simulink - MATLAB & Simulink (mathworks.com). It shows both Simulink and Simscape D...
meer dan een jaar ago | 0
Problems with moving Simscape from 2014b to 2015b
MathWorks does not guarantee behavior when files are saved in a newer release and then opened on an older release. In this case,...
meer dan een jaar ago | 0
Add Reset Function to Simscape Integrator Block
The PS Integrator was updated in R2021a to provide this functionality. The source code is available for that block as well. PS ...
ongeveer 2 jaar ago | 0
i want to learn about the oxygen concentrator example in simscape matlab ?
Hello Hassan, You can find information about it here: Oxygen Concentrator - MATLAB & Simulink (mathworks.com)
meer dan 3 jaar ago | 0
Negative velocity curve from vehicle body block
Hi Vinay, It is difficult to say what happened, but it looks like recreating the subsystem worked. It may be possible that some...
meer dan 3 jaar ago | 0
Source Code Condenser Code
Hi Rainer, A Condenser/Evaporator with two-phase fluid on one side and moist air on the other was introduced in R2019a. A Cond...
meer dan 3 jaar ago | 0
Unexpected dog clutch disengagement behavior
Hello Frank, Thank you for including the example model to demonstrate the issue. The translational behavior of the shift link...
meer dan 4 jaar ago | 1
Unable to open the following model in R2019a trial version.
Hi Sadeer, It looks like the installation is not complete, or the path is incorrect. Definitely contact technical support for...
meer dan 4 jaar ago | 0
Simple gear model with load dependent efficiency
Hi Mahesh, The load-dependent efficiency model assumes that torque loss is equal to a constant value plus an additional loss ...
meer dan 4 jaar ago | 0
How is inertia in planetary gear block calculated?
Hello David, Yes, connecting the carrier port would be the carrier inertia. The planet inertia is the sum of all the planet g...
meer dan 4 jaar ago | 0
I am getting the following error in simscape driveline please help
Hello Mastrieo, This could be due to an overconstrained model. Check to see if you have conflicting parts of the model, for e...
meer dan 4 jaar ago | 0
Thermal behaviour of Harmonic Drive Simulink
Hello Kotryna, Some of this may have been addressed in your other questions. I would also check the Solver Configuration bloc...
meer dan 4 jaar ago | 0
Can't find 'Drive Cycle Source' blockset in Simcsape/Simulink.
Hello Rohan, The Drive Cycle Source is part of the Powertrain Blockset. Check to see if you have that product installed. M...
meer dan 4 jaar ago | 0
| accepted
"First solve for initial conditions failed to converge." Thermal model
Hello Kotryna, The temperature on those blocks is a difference, not absolute. Also focus on specifying the differential varia...
meer dan 4 jaar ago | 0
Initial temperature harmonic drive gear
Hi Kotryana, As a first step, I would look at the Variable Viewer to see what is met and what is not. In the toolstrip, selec...
meer dan 4 jaar ago | 0
Generic engine oscillating output
Hi Stephen, This looks like the oscillation is due to the interactions between the slipping pullies in the two belt drives. I...
meer dan 4 jaar ago | 0
Quarter model with tire (Magic Formula) SimScape Driveline
Hello Marcin, The H port is a translational conserving port associated with the hub of the tire. It should be associated with...
meer dan 4 jaar ago | 0
| accepted
Is it usually used Simscape Driveline for designing the powertrain of a diesel-electric locomotive? Are there any examples about trains?
Hello Stefania, While we do not have any shipping examples regarding trains, users have successfully used Simscape Driveline ...
meer dan 4 jaar ago | 0
How can i see the output torque of a gearbox
Hello Sree, If you need the value during simulation, you could add a Torque Sensor from the Simscape Foundation Library in se...
meer dan 4 jaar ago | 0
Looking for Leadscrew model in library and not found.
Hello Orlando, Do you have Simscape Driveline installed? This block is in the Simscape Driveline library under Gears and Rota...
meer dan 4 jaar ago | 0
| accepted
Torque vector must be arranged in strictly ascending order.
The block is not erroring because of the torque vector given on the Engine Torque tab. Speed is the independent vector that must...
ongeveer 5 jaar ago | 0
Disk Friction Clutch - OPEN clutch
Hello Berkan, There are two types of kinetic friction in the model. The kinetic friction of the clutch plates pushing against...
ongeveer 5 jaar ago | 0