photo

J Chen


Last seen: ongeveer 2 maanden ago Active since 2019

Followers: 0   Following: 0

Statistics

All
  • 5-Star Galaxy Level 2
  • 36 Month Streak
  • Thankful Level 2
  • Knowledgeable Level 4
  • Personal Best Downloads Level 2
  • Revival Level 2
  • GitHub Submissions Level 3
  • Thankful Level 1
  • First Review
  • First Submission
  • First Answer

View badges

Feeds

View by

Answered
Are Simscape's Principal Axes in a particular order from least to greatest moment of inertia?
The axes of the Inertia Sensor are the same as the axes of the frame that the sensor is attached to.

9 maanden ago | 0

Answered
The issue encountered during the simulation of the Stewart platform: "The motion is singular."
Make sure the mechanism is not over-constrained. Add inertia between two connected joints.

9 maanden ago | 0

Answered
simscape electrical long-term simulation
Yes. You can adjust the solver parameters in the Simulink Model Settings.

9 maanden ago | 0

Answered
Simscape PS converter error
The filter in the PS converter is not used to filter the command in conentional sense. The filter is used to make a system solva...

10 maanden ago | 0

Answered
Rigid Transform input data sequence
Use a rotation joint (such as the gimbal joint) and connect it to a solid. Specify motion indtead of torque as actuation. Here i...

10 maanden ago | 0

Answered
How to observe the acceleration profile of a pneumatic (cylinder) system?
Mechanical sensors can be used to measure acceleration - Link.

10 maanden ago | 1

Answered
Using a Simulink dynamic motorcycle in a driving scenario trajectory.
You need to use a lateral controller such as Pure Pursuit (in the Navigation or Robotics toolbox) or Stanley (in the Automatic D...

ongeveer een jaar ago | 0

| accepted

Answered
How to access the eigenvalues and eigenvectors of a M-DOF system built in Simscape?
You can linearize the Simscape model.

ongeveer een jaar ago | 0

Answered
Building a nonlinear spring in Multibody
You can use the Trnasform Sensor block to sense motion, convert the output to Simulink signals, calculate corresponding forces u...

ongeveer een jaar ago | 0

Answered
Failed to load library 'RP_Simulator_Components' referenced by
You can download the library from https://www.mathworks.com/matlabcentral/fileexchange/67157-robotics-playground

ongeveer een jaar ago | 0

Answered
My "generic engine" block seems to not care about the throttle input.
The attached file contaons a running example. These are my suggestions: It seems that some inertia need to be associated with t...

ongeveer een jaar ago | 0

Answered
Free Fallen object simulation
You can use the Block Solid in the Body Elements. Also use the Transform Sensor in the Frames and Transforms to measure the tran...

meer dan een jaar ago | 0

Answered
About adding motion directly to the end-effector
Connect a 6 DoF joint to the end effector and ground. Specify the displacements of the 6 DoF joint. Rember to set the Filtering ...

meer dan een jaar ago | 0

Answered
Number of variables vs number of equations in Simscape components
For a Simscape component, the variables include variables in the variables AND nodes sections as in this example. The number of ...

meer dan een jaar ago | 0

Answered
No simscape simulation log
Open Model Settings (ctrl-E). Select Data Import/Export. Uncheck Single simulation output.

meer dan een jaar ago | 0

Answered
Programmatically connect SimScape blocks
set_param('mymodel/Res2','position',[220,120,180,160]) is wrong. The third number (180) needs to be greater than the first numb...

meer dan een jaar ago | 0

Answered
simulink-ps converter output with on signal
You should see the signal at both scopes. Make sure the axis scalings are appropriate.

meer dan een jaar ago | 0

Answered
Need to assemble a submarine in simscape multibody make it move according to the precalculated trajectory. 1) All details of submarine are separated 2) How to make it move?
All components are rigidly connected in the model. You need to remove a solid line and add a joint between two components to mak...

meer dan een jaar ago | 0

| accepted

Answered
How to use the DATA Inspector with SimScape model
You need to use Sensors and Transducers block to measure the variables, then convert the Simscape signals to the Simulink signal...

meer dan een jaar ago | 0

Answered
Is it possible to open matlab function block editor code in the standard script editor?
One option is to right click at the block and choose Open in New Window.

meer dan een jaar ago | 0

Answered
Communicating Simscape multibody with temperature and pressure sensors
Simscape Multibody doesn't deal with heat and temperature. You need to build a thermal model either with the Thermal Library in ...

bijna 2 jaar ago | 0

| accepted

Answered
how to attach custom frame to cylindrical solid
You can use the Rigid Transform block as an alternative.

bijna 2 jaar ago | 0

Answered
Extract Spring data from the revolut joint
Expand the Sensing fiels and check the position. A port will appear to output the position. Use a PS-Siumulink Converter block i...

bijna 2 jaar ago | 0

Answered
ssc_mass_spring_damper_control example, all forces become 0 when no feedback?
The mass is stationary and the spring and damper generate no force at time zero. No force is applied to the mass if the PID is r...

bijna 2 jaar ago | 0

Answered
Is there any two wheeler drive cycle file in MATLAB or simulink?
You can download the speed profile in Excel at (https://cleanfuturemobility.com/driving-cycles/) and import it into Matlab/Simul...

bijna 2 jaar ago | 0

| accepted

Answered
SIMSCAPE MULTIBODY: Apply Forces / Sense velocity of GLOBAL Center of Mass
First add a new frame to the Center of Gravity (CoG). Connect a 6 DoF Joint between the new frame to the World Frame. Specify ...

bijna 2 jaar ago | 0

Answered
How to get the coordinates of points in the simulink multibody model?
You can add a Transform Sensor to your system.

bijna 2 jaar ago | 0

Answered
How to loop a model's output back to the input untill they both converge
Use a Delay block https://www.mathworks.com/help/simulink/slref/delay.html

ongeveer 2 jaar ago | 0

| accepted

Answered
(Simscape multibody) Is there any way to use a specific angle as a input for revolute joint?
Set the Actuation tab as follows: Torque - Automatically computed, Motion - Provided by Input. You also need Simulink-PS Convert...

ongeveer 2 jaar ago | 0

Answered
Generic Engine stalling when load applied
You need to specify an initial speed for the propeller. It is done in the Variables tab of the Propeller Inertia block.

ongeveer 2 jaar ago | 0

Load more