photo

Aditya Padmanabha

Last seen: Today |  Active since 2017

Followers: 0   Following: 0

Statistics

All
  • 3 Month Streak
  • Revival Level 3
  • Knowledgeable Level 2
  • First Review
  • Solver
  • First Answer

View badges

Feeds

View by

Answered
How to integrate freeRTOS to C2000 blocksets?
Hi Sudam, Currently the option to integrate FreeRTOS is not avaliable from C2000 Microcontroller Blockset for now. The only way...

6 maanden ago | 0

| accepted

Answered
No ePWM output with reference to ADC input while using Launchxl-F28379D
Hi Rahul, If we consider 25KHz as the frequency of Sine wave and if we consider atleast 10 signal samples per one sine wave c...

meer dan 2 jaar ago | 0

| accepted

Answered
hello i want to know the ADC input of current and voltage sensor
Hi Hazma, You can use the block in the model directly and set the required parameters. The output port from the block will gi...

meer dan 2 jaar ago | 0

Answered
F28388D Simulink model failed to boot from flash
Hi All, In Case of TI F2838x you need to flash all the cores with executable generated from same version of support package. ...

meer dan 2 jaar ago | 0

Answered
Not able to synchronize ADC with PWM in F28379D TI launchpad.
Hi Anurag, Couple of points to look out In the attached model, the ePWM1 is configured to trigger ADC at 3rd event instead o...

bijna 3 jaar ago | 0

Answered
TI C2000 Delfino - Setting up a software SOC trigger for an ADC in Simulink
Hi Aryaman, Please refer to the following pages which explains or showns how to configure SOC for ADC. Configure ADC to samp...

ongeveer 3 jaar ago | 0

Answered
Error in PIL execution for F28027 C2000 TI MCU
Hi Sanjeev, Pleace change the dataype of the inputs to Single instead of double. Double is represented as 32-bit floating poi...

ongeveer 3 jaar ago | 0

Answered
TMS320F28379D problem loading Code
Hi rida, Please follow the shipping example which explains how to do a simple model to blink a LED on C2000 hardware board. G...

ongeveer 3 jaar ago | 0

Answered
Important Question Processor In the Loop Application using C2000 Embedded Coder
Answer posted in comments https://www.mathworks.com/matlabcentral/answers/597754-important-question-processor-in-the-loop-applic...

ongeveer 3 jaar ago | 0

Answered
Embedded Coder C2000 Example F28069 does not support generating C++ Code
Hi Felix, Yes as of now only C workflow is supported for the TI C2000 support package. Thanks, Aditya

ongeveer 3 jaar ago | 0

Answered
Cannot connect to Launchpad TMS320F28379D Development Kit
Hi HongPong, Akash, Please configure the support package after installation. To configure the support package, you can go to ...

ongeveer 3 jaar ago | 1

Answered
XCP Parameter Granularity Error (TI C2000)
Hi Guido, Roberto, The XCP external mode does not support data logging and parameter tuning of Uint8/int8 parameters for TI C2...

ongeveer 3 jaar ago | 1

| accepted

Answered
Random Simulink TI C2000 build error: Code generation information file does not exist
Hi Clemens, Please try the following and if that does not solve the problem please contact Technical Support: www.mathworks.com...

ongeveer 3 jaar ago | 1

| accepted

Answered
I'm trying to use SPI communication using C2000, how to control the slave select pin ,what settings should be selected in hardware implementation? ?
Hi Jyoti, Please check the FAQ on this topic What are the use case scenarios for SPI (Master Transfer/Transmit/Receive) block...

ongeveer 3 jaar ago | 0

Answered
C2000 hardware interrupt
Hi Mark, In the example, when you send data to SPI transmit block, the data continuously shifts of the transmit register. Th...

ongeveer 4 jaar ago | 1

Answered
C2000 CLA trigger using ADCINT source
Hi Zak, Please set the properties of the signal at ADC output to Cla1DataRam memory so that the variable is created in cla. ...

bijna 5 jaar ago | 1

| accepted

Answered
Flash programming TI LAUNCHXL-F28379D
Hi Marco, Can you provide the version of MATLAB and Code Composer Studio you are using? Thanks, Aditya

meer dan 5 jaar ago | 0

Answered
Sending an integer from one F28379D board to another F28379D board using SCI
Hi Christos, Which board are you using? ControlCard or LaunchPad? For ControlCard External mode uses SCI_A module with GPI...

ongeveer 6 jaar ago | 0

Answered
SPI receive block on F28335 connect with Arduino Nano timeout error
Hi Jirada, You need to ensure the SPI clock mode match properly between Arduino Nano and F28335. For example, * If you ...

meer dan 6 jaar ago | 0

Answered
How to configure TMS320f28379D launchpad?
Hi, The maximum voltage that you can use as input should be limited to 3.3V. If the voltage is greater than 3.3V it may damag...

meer dan 6 jaar ago | 0

Answered
SPI receive - TI LAUNCHXL-F28379D
Hi Oleg, Please use the latest update of the support package - "18.1.2" (in the MATLAB main window go to Add-Ons --> Check fo...

meer dan 6 jaar ago | 0

Answered
Unable to read data from the MPU6050 with TI C2000 f28379d & Simulink
Hi Tommaso, I have attached the 17a model for the MPU-9150 present on BOOSTXL_SENSHUB attached to F28379D LaunchPad based on ...

meer dan 6 jaar ago | 0

| accepted

Answered
I can't use SPI on F28M36 concerto C2000
Hi, The SPI SIMO and CLK pins should have values at the pins even though you are not reading the SOMI data using SPI Receive....

bijna 7 jaar ago | 0

| accepted

Answered
C2000 LAUNCHXL-F28379D: SIMULINK I2C BLOCK
Hi Jed, Did you look at the updated I2C examples shipped in R2017a http://www.mathworks.com/help/supportpkg/texasinstrumentsc...

ongeveer 7 jaar ago | 0

Answered
Unable to use eCAP4 to eCAP6 on TMS320F28377S
Hi, Thanks for pointing out the issue. This issue has been fixed and updated in the latest support package release. -Adity...

bijna 8 jaar ago | 0