photo

jarul


Last seen: bijna 2 jaar ago |  Active since 2019

Followers: 0   Following: 0

Statistics

All
  • Thankful Level 2
  • Thankful Level 1
  • First Answer
  • First Submission
  • Explorer
  • First Review
  • Revival Level 1

View badges

Feeds

View by

Question


SD card image creation not Successful.
I created my SD card image with the "Manual Host-Radio Hardware Setup" Now when I inserted the SD Card on my FPGA, I try to pin...

ongeveer 3 jaar ago | 0 answers | 0

0

answers

Question


Quesiton about transmitRepeat(sdrTransmit, data) and sdrTransmit.Repeat(txWavefrom)
While working on SDR, I realize that earlier Matlab used transmitRepeat and now it is changed to sdrTransmit.Repeat method. Now...

meer dan 4 jaar ago | 2 answers | 0

2

answers

Answered
Zynq SDR Capture Length question!
I have another question related to the above issue. When I tried to transfer rather large size, I get the following error. G...

meer dan 4 jaar ago | 0

Question


Zynq SDR Capture Length question!
While using Zynq SDR, the capture length can not exceed '16777216'. I want to capture length longer than the prescribed. I get ...

meer dan 4 jaar ago | 2 answers | 0

2

answers

Question


The following Matlab code runs only half of the for loop. Can anyone help me figure out the problem?
Here is the part of the matlab Code that I was working for an SDR development. In the following code, when the ind in the for l...

meer dan 4 jaar ago | 1 answer | 0

1

answer

Answered
Why do I encounter "something Unexpected Occurred" after installing the "Xilinx Zynq-Based Radio, or USRP Embedded Series Radio" support packages?
Hai Colin, Thanks for your response. I was able to setup the AD9361 SDR successfully. The method mentioned in the mathworks we...

bijna 5 jaar ago | 0

Question


Error using R2019b version of the MATLAB
Just installed R2019b MATLAB. SDR with AD9361 is attached to the Host machine. The host machine's IP is set to 192.168.3.1 Th...

bijna 5 jaar ago | 6 answers | 0

6

answers

Answered
Why do I encounter "something Unexpected Occurred" after installing the "Xilinx Zynq-Based Radio, or USRP Embedded Series Radio" support packages?
I have installed just one communication toolbox as shown below: "Communications Toolbox Support Package for Xilinx Zynq-Based R...

bijna 5 jaar ago | 0

Answered
Error using R2019b version of the MATLAB
This morning I reinstalled R2019b ones again deleting the previous install of R2019b. I just ran the simple code to test the ca...

ongeveer 5 jaar ago | 0

Answered
Error using R2019b version of the MATLAB
Thanks for your response. My host machine is setup in 192.168.3.1 My radio is setup in 192.168.3.14 I can ping 192.168.3.14 a...

ongeveer 5 jaar ago | 0

Answered
Error using R2019b version of the MATLAB
Just to respond to your answer: Have been working on SDR AD9361 software quite sometime. One host computer is setup Linux Ubun...

ongeveer 5 jaar ago | 0

Answered
R2019b version and AD9361 SDR does not work correctly.
This has been reported many times, but not fixed for a month or so. I need to do further experiment. Kindly take a closer look ...

ongeveer 5 jaar ago | 0

Answered
Error using R2019b version of the MATLAB
To answer the above query: I am using Ubuntu 18.04 The SDR hardware is Z706 and AD9361. The libiio I am using the same since ...

ongeveer 5 jaar ago | 0

Question


R2019b version and AD9361 SDR does not work correctly.
I have installed R2019b version of the Matlab. After installing, the matlab meant for SDR does not work correctly. Even the fo...

ongeveer 5 jaar ago | 2 answers | 0

2

answers

Question


While installing "SoC Blockset Support Package for Xilinx Devices" I have the following outcome.
Xilinx Zynq Radio Linux binaries are not installed. The third party software download error occurs. This problem has not been ...

ongeveer 5 jaar ago | 1 answer | 0

1

answer

Answered
TWO SDR using AD9361 transmitting and receiving image problem!
I have been trying to install the Linux version of the Xilinx Zynq Radio to run SDR software for single radio. I have spend seve...

ongeveer 5 jaar ago | 0

Question


ERROR '/home/jarul/Documents/MATLAB/SupportPackages/R2019b/toolbox/target/supportpackages/shared_linuxservices/+matlabshared/+internal/ssh2client.p'
While using MATLAB R2019b version, running SDR transmitter using AD9361 or the simulink, I get the following error. How to solv...

ongeveer 5 jaar ago | 1 answer | 0

1

answer

Question


"Error using matlabshared.internal.ssh2Client"
With R2019b version installed I can not run AD9361 SDR software. The transmit and receive functions can not be run. I get the ...

ongeveer 5 jaar ago | 3 answers | 0

3

answers

Question


MATLAB 2019b Installation of SDR for Xilinx zynq Radio problem.
I have installed MATLAB 2019b version. I want to test the code for SDR. However, I can not install the following libraries nece...

ongeveer 5 jaar ago | 1 answer | 0

1

answer

Question


Install Communication ToolBox Support Package for Xilinx zynq Based Radio on MATLAB 2019b
While trying to install "Communication ToolBox Support Package for Xilinx zynq Based Radio on Matlab 2019b" Can not install xil...

ongeveer 5 jaar ago | 1 answer | 0

1

answer

Question


TWO SDR using AD9361 transmitting and receiving image problem!
Any Mathworks group can help me with the following problems. I am running two different SDRs with different IPs and a host mach...

meer dan 5 jaar ago | 1 answer | 0

1

answer

Answered
SDR using AD9361 multi-FMCOMMS I get the following error.
Thanks for your response. Yes, the Code (Transmit and Receive LTE MIMO) works fine for a single SDR fine. However, when I run on...

meer dan 5 jaar ago | 0

| accepted

Question


SDR using AD9361 multi-FMCOMMS I get the following error.
I ran the following MATLAB code and get the following error code: Transmit and Receive LTE MIMO using Analog Devices AD9361/AD9...

meer dan 5 jaar ago | 2 answers | 0

2

answers