Statistics
RANK
175
of 294.438
REPUTATION
650
CONTRIBUTIONS
0 Questions
297 Answers
ANSWER ACCEPTANCE
0.00%
VOTES RECEIVED
131
RANK
3.209 of 20.114
REPUTATION
488
AVERAGE RATING
4.00
CONTRIBUTIONS
1 File
DOWNLOADS
4
ALL TIME DOWNLOADS
4833
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Feeds
Submitted
Monte Carlo Simulation with Simulink
Select blocks to vary parameters for Monte Carlo Simulation.
ongeveer 8 jaar ago | 4 downloads |
Solved
Add a block to a model
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-block-eqn.png>> In this case, the slope of...
ongeveer 9 jaar ago
Solved
Produce a cosine wave
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/cosine-eqn.png>>
ongeveer 9 jaar ago
Solved
Connect blocks in a model
Connect the blocks in the model to produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/connect-blocks...
ongeveer 9 jaar ago
I am using Matlab R2011a. I am creating any circuit model in Simulink, and after I simulate, an error log opens saying initialisation commands cannot be evaluated, hw to solve?
Based on the error it sounds like you are utilizing SimPowerSystems. Those blocks require the powergui to determine the solver....
meer dan 9 jaar ago | 1
| accepted
How to include a slider GUI in a Simuink Model?
You could potentially build a slider as part of a <http://www.mathworks.com/help/simulink/gui/parameters-pane.html mask>. Oth...
bijna 10 jaar ago | 0
Solved
Create times-tables
At one time or another, we all had to memorize boring times tables. 5 times 5 is 25. 5 times 6 is 30. 12 times 12 is way more th...
ongeveer 10 jaar ago
I need a simulink modeling T.C.S (Traction controll system ) or A.B.S (Anti brake System)
There is a complete car model available: http://www.mathworks.com/help/physmod/sdl/ug/complete-car-model-and-simulation.h...
meer dan 10 jaar ago | 1
Calling Planetary EphemerisSimulink Block From .m file. The resulting output is unclear.
Did you try starting from the example? Implement the position and velocity for Saturn with respect to the Solar System baryce...
meer dan 10 jaar ago | 1
How does the (Embedded) MATLAB Function work in Simulink
Thanks for the well written questions. 1) The function regenerates anytime you change the MATLAB function or parameters withi...
meer dan 10 jaar ago | 1
How to use SISO Design tool for a simulink model?
If you're using R2012b or later, in Simulink go to analysis -> Control Design -> Control System Designer. It's a big more a...
meer dan 10 jaar ago | 1
| accepted
List containing all parameters that can be set by set_param
ParameterCellArray = get_param(gcb, 'DialogParameters') returns a cell array containing the names of the Object dialog pa...
meer dan 10 jaar ago | 2
| accepted
symbolic state space representation & transfer function
Symbolic representation is not compatible with the controls tools. You would have to do this manually.
meer dan 10 jaar ago | 0
| accepted
Changing Simscape Block Properties during simulation
Depending on your implementation this may work (post a picture of what you've got or upload a model for better answer). You c...
meer dan 10 jaar ago | 1
quick loging and un-logging of Simulink signals
From 13b release notes: http://www.mathworks.com/help/simulink/release-notes.html Data Management Streamlined selection...
bijna 11 jaar ago | 0
| accepted
Can a Switch block handle signals of Mux?
Without fully understanding your setup, all inputs to a switch must have the same size. For example, if you have a mux with 2 e...
bijna 11 jaar ago | 0
Contact modeling between two bodies
I'm not sure the ideal way to do this, but off the top of my head I think you would want to set up a conditional for when they c...
bijna 11 jaar ago | 1
| accepted
how can i see the live value on my Simulink Modell during Simulation
Try <http://www.mathworks.com/help/simulink/ug/displaying-block-outputs.html show port value display>
bijna 11 jaar ago | 0
Modelling a Quadrotor with Simmechanics
Depending on what you're looking to do, this can be done with either Aero Blks or SimMech. From scratch, aero blks is easier be...
bijna 11 jaar ago | 0
Simulink rapid acceleration creates temp files which fill drive
What's your parfor loop look like? You might be able to do something like parfor i = 1:100 eval(['myOutput' num2str...
bijna 11 jaar ago | 0
Reported 'algebraic loop error' when I was using feed back in logic simulation.
http://www.mathworks.com/help/simulink/ug/simulating-dynamic-systems.html#f7-19688 Long story short, the input of the highlig...
bijna 11 jaar ago | 0
Is it possible to estimate the Transport Delay within a Simulink model using the Simulink Design Optimization toolbox?
You can set the delay in the transport to a workspace variable. You can then bring the workspace variable into the optimization...
bijna 11 jaar ago | 0
| accepted
Brewery Manufacturing Process Simulation
Try <http://www.mathworks.com/help/simevents/ug/generating-multiple-entities-at-simulation-start.html generating entities at sim...
bijna 11 jaar ago | 1
How do you represent contact with the ground in simscape?
You want the <http://www.mathworks.com/help/physmod/simscape/ref/translationalhardstop.html translational hard stop> block. ...
bijna 11 jaar ago | 0
Documentation for expamples on simulink for beginners
I would start with the Simulink examples on the <http://www.mathworks.com/products/simulink/examples.html?s_tid=sima_nav_ve prod...
bijna 11 jaar ago | 0
Simulink with Simscape make mistake while calculating derivative
It appears to be a units issue, at least with your understanding of the mathematics. Put the frequency in as 1/(2*pi) hz, equiv...
bijna 11 jaar ago | 0
How to process mat-files saved by Simulink Data Inspector in Matlab?
You should check out the <http://www.mathworks.com/help/simulink/ug/record-and-inspect-signal-data-programmatically.html SDI API...
ongeveer 11 jaar ago | 0
[Simulink] Rate limiter dynamic with a variable-step solver
You could put a rate transition on the input signal to the block. This would make the input signal fixed sample time and resolv...
ongeveer 11 jaar ago | 0
Rate Limiter Block Error
Try changing the sample time of the step to either -1 or a sample rate. The problem is the default rate is 0, which is neither ...
ongeveer 11 jaar ago | 1
Why is their an offset when I intergrate a simple sin(1*x) in simulink using the (1/s) block?
You need to set the <http://www.mathworks.com/help/simulink/slref/integrator.html initial condition> of the integrator. I belie...
ongeveer 11 jaar ago | 0