photo

Torsten Knodt


A123 Systems GmbH

Last seen: bijna 2 jaar ago |  Active since 2012

Followers: 0   Following: 0

Message

Professional Interests: Rapid Prototyping, Ground Vehicle Physical Simulation, Virtual Integration, Model Based Development, AutoSAR, Symbolic Solutions to Differential Equations, Static and Dynamic Parameter Estimation

Statistics

All
  • First Review
  • Thankful Level 1
  • Revival Level 1
  • Knowledgeable Level 1
  • First Answer
  • Scavenger Finisher
  • Commenter
  • Solver

View badges

Feeds

View by

Question


How to continuously repeat the output of the "From Spreadsheet" source block?
Hi, How can I continuously repeat the output of the "From Spreadsheet" source block? The extrapolation at the end does not pro...

bijna 5 jaar ago | 1 answer | 0

1

answer

Question


How can I draw a mesh into a block mask/ icon?
Hello, I have a masked Simulink block. Now I want to draw a mesh into the icon. Unfortunately the mesh is drawn into an own w...

bijna 8 jaar ago | 1 answer | 0

1

answer

Solved


Compute the step response of a DC motor
Compute the step response of a DC motor shown below <<http://blogs.mathworks.com/images/seth/cody/dc-motor.png>> The param...

ongeveer 8 jaar ago

Solved


Counting pulses in a signal
Count the number of pulses that are the result of summing each pulse generator block. Pulse Generator blocks produce a recurr...

ongeveer 8 jaar ago

Solved


Make a low pass filter
Make a first order low pass filter that will filter out the high frequency oscillations for the given input signal. The cut-off ...

ongeveer 8 jaar ago

Answered
Automotive problem - Counting and saving
This depends on your interface to write to the EEPROM. Normally you would count in your RAM and trigger writing to the EEPROM in...

ongeveer 8 jaar ago | 0

Solved


Add offset to a signal
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-offset-eqn.png>> You should see a downward...

ongeveer 8 jaar ago

Solved


Produce a sine wave
Produce a sine wave with amplitude 3: <<http://blogs.mathworks.com/images/seth/cody/sine-eqn.png>>

ongeveer 8 jaar ago

Solved


Produce a cosine wave
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/cosine-eqn.png>>

ongeveer 8 jaar ago

Solved


Connect blocks in a model
Connect the blocks in the model to produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/connect-blocks...

ongeveer 8 jaar ago

Solved


Add a block to a model
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-block-eqn.png>> In this case, the slope of...

ongeveer 8 jaar ago

Solved


Make the vector [1 2 3 4 5 6 7 8 9 10]
In MATLAB, you create a vector by enclosing the elements in square brackets like so: x = [1 2 3 4] Commas are optional, s...

ongeveer 8 jaar ago

Solved


Pizza!
Given a circular pizza with radius _z_ and thickness _a_, return the pizza's volume. [ _z_ is first input argument.] Non-scor...

ongeveer 8 jaar ago

Answered
How can i change a value of a resistor during simulation using simpowersystems toolbox ( R L C branch )
I had the same requirement. I either use a voltage measurement together with a controlled current source or a current measureme...

meer dan 8 jaar ago | 0

| accepted

Question


/usr/bin/ld: raccel_sfcn_utils.o: undefined reference to symbol 'dlclose@@GLIBC_2.2.5'
I get the following message when starting a simulation in rapid acceleration mode under Ubuntu Xenial 64 Bit which works under W...

meer dan 8 jaar ago | 0 answers | 0

0

answers

Question


What is the cause of the error message "FIMATH mismatch:Property 'ProductWordLength'" here?
I get the error message FIMATH mismatch:Property 'ProductWordLength': 16 ~= 32 from the following action code in a stat...

meer dan 8 jaar ago | 1 answer | 0

1

answer

Answered
How to define the sampling time in a system of Simscape Power System Blocks without accuracy lost importants?
Hi Tony, it's hard to give an advice without knowing your model, simulation settings and the intent of your simulation. Becaus...

meer dan 8 jaar ago | 0

| accepted

Question


OutOfMemoryError when building PDF System Design Description for "big" Simulink Model
Hello, I get an OutOfMemoryError when building a System Design Description in PDF and Word format. I already increased the heap...

ongeveer 9 jaar ago | 0 answers | 0

0

answers

Question


Initial output value for bus in enabled subsystem hierarchy
I have a hierarchy of subsystems where a middle subsystem is an enabled one. The hierarchical subsystems each have a single outp...

ongeveer 10 jaar ago | 1 answer | 0

1

answer

Question


Analyzing and creating fixed-point data types.
Hello, is there a single function to get the minimum and maximum value representable by a specific fixed-point data type? I am ...

bijna 12 jaar ago | 1 answer | 0

1

answer

Question


Simulink message "Attempt to use invalid data type id 17"
Hello, how can I find out which data type corresponds to a specific id when getting the message "Attempt to use invalid data ty...

meer dan 12 jaar ago | 1 answer | 2

1

answer

Question


"Variable time delay" block in "For Each Subsystem"
Hello, I try to synthesize noise coming from multiple targets to multiple sensors. I have two cascaded for-each sub-systems, th...

meer dan 12 jaar ago | 1 answer | 0

1

answer