Plotting data from adc in matlab

code is below. How can I plot the dene[i] in code in matlab?

#include <stm32f4xx.h>

#include <stm32f4xx_conf.h>

#include <stm32f4xx_rcc.h>

#include <stm32f4xx_adc.h>

#include <stm32f4xx_gpio.h>

ADC_InitTypeDef ADC_init_structure; //Structure for adc confguration

GPIO_InitTypeDef alper; //Structure for analog input pin

int i;

static char dene1[2048];

static char dene2[2048];

static char dene3[2048];

static char dene4[2048];

static char dene5[1808];

float dum1;

int ms10Ticks; /* counts 1ms timeTicks */

/*----------------------------------------------------------------------------

SysTick_Handler

*----------------------------------------------------------------------------*/

void SysTick_Handler(void) {

ms10Ticks++;

ADC_SoftwareStartConv(ADC1);//ADC1->CR2 |= (1<<30);

}

/*----------------------------------------------------------------------------

MAIN function

*----------------------------------------------------------------------------*/

int main (void) {

RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD,ENABLE);

RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOC,ENABLE);

RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1,ENABLE);

GPIO_StructInit(&alper);

alper.GPIO_Pin = GPIO_Pin_5;//The channel 15 is connected to PC5

alper.GPIO_Mode = GPIO_Mode_AN; //The PC5 pin is configured in analog mode

alper.GPIO_PuPd = GPIO_PuPd_NOPULL; //We don't need any pull up or pull down

GPIO_Init(GPIOC,&alper);//Affecting the port with the initialization structure configuration

//GPIOC->MODER |= (3<<10); // PC5--> ADC.15 input olarak ayarla

//GPIOC->PUPDR = 0x00000000; // pull up-down yok

ADC_DeInit();

ADC_init_structure.ADC_DataAlign = ADC_DataAlign_Right;//data converted will be shifted to right

ADC_init_structure.ADC_Resolution = ADC_Resolution_12b;//Input voltage is converted into a 12bit number giving a maximum value of 4096

ADC_init_structure.ADC_ContinuousConvMode = DISABLE; //the conversion is continuous, the input data is converted once

ADC_init_structure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;//no trigger for conversion

ADC_init_structure.ADC_NbrOfConversion = 1;

ADC_init_structure.ADC_ScanConvMode = DISABLE;//The scan is configured in one channel

ADC_Init(ADC1,&ADC_init_structure);//Initialize ADC with the previous configuration

//Enable ADC conversion

ADC_Cmd(ADC1,ENABLE);

//Select the channel to be read from

ADC_RegularChannelConfig(ADC1,ADC_Channel_15,1,ADC_SampleTime_144Cycles);

SystemCoreClockUpdate(); /* Get Core Clock Frequency */

if (SysTick_Config(SystemCoreClock / 10000)) { /* SysTick 10 msec interrupts */

while (1); /* Capture error */

}

while(1) { /* Loop forever */

if(ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC)){//if((ADC1->SR & 0x00000002))

if(i<2048)

dene1[i]=(ADC_GetConversionValue(ADC1));

else if(i>2048 && i<4096)

dene2[i-2048]=(ADC_GetConversionValue(ADC1));

else if(i>4096 && i<6144)

dene3[i-4096]=(ADC_GetConversionValue(ADC1));

else if(i>6144 && i<8192)

dene4[i-6144]=(ADC_GetConversionValue(ADC1));

else

dene5[i-8192]=(ADC_GetConversionValue(ADC1));

i++;

if(i==10000){

i=0;

}

}

}

}