Answered
Did anyone already use DMA with F28M36 ?
Please update on the version of MATLAB you are using?

7 years ago | 0

Answered
ePWM setting for C2000 DSP, output not the right frequency
Hi Mike, Regarding your point of 'Also, if I look at ePWMA and ePWMB panes setting, is there a mistake for ePWMB output pane ...

7 years ago | 0

| accepted

Answered
ePWM setting for C2000 DSP, output not the right frequency
Please share your model and provide MATLAB version details, and Hardware version details for further investigation.

7 years ago | 0

Answered
Simulink compilation error: Launchpad F28069M
Looks like your model is stuck in external mode configuration which happens to be a intermediate config set that is used in back...

7 years ago | 1

| accepted

Answered
How do I generate complementary signals on ePWMA and ePWMB with F28335 using Simulink ePWM block?
Please mention the version of the MATLAB and version of the C2000 hardware support package that you are working with.

7 years ago | 0

Answered
The Embedded Coder for the TI c2000 F2837xD builds and compiles but does not deploy to hardware only when some blocks are used?
Please refer the link: https://in.mathworks.com/matlabcentral/answers/358275-how-to-create-and-open-a-code-composer-studio-ccs-...

7 years ago | 0

Answered
The Embedded Coder for the TI c2000 F2837xD builds and compiles but does not deploy to hardware only when some blocks are used?
I think the log you have attached is quite normal. After the programming is running from target, it is a standalone application ...

7 years ago | 0

Answered
Usage of C2000 TI family launch pad F28069M without Embedded coder
Yes, you can generate code from Simulink coder/Matlab coder and work with C2000 target. But Embedded coder provides more option ...

7 years ago | 0

Answered
How to measure task execution time on F28379D target?
This feature is not supported in MATLAB 2016b. Please consider upgrade to 2017a or later where this feature is introduced.

7 years ago | 0

Answered
How to measure task execution time on F28379D target?
Please mention the MATLAB version and attach the Model file if possible.

7 years ago | 0

Answered
I am trying to generate PWM for F28335 with CCSV6 with simulink coder. C code is generated when I am trying to "Deploy to Hardware" an error occurred. The diagnostic report is attached.
Hi, Run the 'targetupdater' and complete the hardware setup once. You could also provide the details of the path of tools th...

7 years ago | 0

Answered
Problem in programming 28379D from Simulink
Hi, Please try to connect to board from CCS and see if you are successful. Do you see the device listed under device manager?...

7 years ago | 1

Answered
Code generated by Simulink Embedded Coder runs slower as more coded added, why?
Hi, If the execution time is larger than the sample time, we are in an overrun situation. We want to keep the execution time ...

7 years ago | 0

Answered
Program the TI F28335 for CAN communication
Hi, Please update on the MATLAB version being used. Regards, Venkatesh C

7 years ago | 0

Answered
How to enable the MCU's internal pullup/pulldown resistors at Embedded Coder Support Package for Texas Instruments C2000 Processors?
Hi Gabriel, There is no Pulldown circuit. You need to add an external one if required. If pullup is disabled, the pin would b...

7 years ago | 0

Answered
How to enable the MCU's internal pullup/pulldown resistors at Embedded Coder Support Package for Texas Instruments C2000 Processors?
HI, If you can try the following: Please use the "System Initialize" block found under "Simulink coder->Custom Code" lib...

7 years ago | 0

| accepted

Answered
Problem with TI TMDSHVMTRINSPIN+F x hardware (C2000 processors)
Hi Galo, Your approach should work considering the fact that both Kits are the same with only a subtle difference that the 'T...

8 years ago | 0

Answered
LaunchXL-F28379D in External Mode. I only got last few values when I save a signal "To Workspace", any idea of the reason?
Hi Josep, Use a hardware trigger for ADC conversion and see if it helps. I have model attached in which I am triggering ADC ...

8 years ago | 0

Answered
I cannot find c2000 as well as target preferences in embeded coder in matlab 2016a?is it there or c5000 is only there?
Please try this one: https://www.mathworks.com/help/supportpkg/texasinstrumentsc2000/ug/install-support-for-c2000-processors....

8 years ago | 0

Answered
With 28335 TI, embedded coder, for a sine signal with and without presence of ADC block frequency is changing
The likely reason for this is overrun issue of the step function. You may consider reducing the sample time of the step functio...

8 years ago | 0

Answered
With 28335 TI, embedded coder, for a sine signal with and without presence of ADC block frequency is changing
Hi, Please send us the model. Regards, Venkatesh C

8 years ago | 0

Answered
Simulink CAN timeout on embedded coder
You can create a counter and reset it when you get a CAN message (from the function call of the CAN block or an interrupt). If t...

8 years ago | 0

Answered
the third party installation package got skipped while installing Add ons.
You can ignore the warning for now and start using the support package. Please update for any issues encountered during the time...

8 years ago | 0

Answered
CCS/F28M36P63C2: Can't compile an auto generated code from Simulink.
https://www.mathworks.com/matlabcentral/answers/382607-ccs7-unsupported-by-matlab-simulink

8 years ago | 0

| accepted

Answered
Simulink model doesn't look configured for the Texas Instruments' F28379D processor
Make sure to select the System Target file as ert.tlc under code generation pane.

8 years ago | 0

| accepted

Answered
Cant get complete adc data using c2000 in external mode
Please run through TASK 3 from link below and see if it helps: https://www.mathworks.com/help/supportpkg/texasinstrumentsc2000/...

8 years ago | 0

Answered
CCS7 unsupported by Matlab/Simulink ?
Could you please update on the version of the support package? 17.2.2 is latest, please let us know which version is installed ...

8 years ago | 0

Answered
How can I call assembler code DSP28x_usDelay() in a simulink model
Please use Atomic subsystem and place the customer code block from Simulink coder -> custom code -> system outputs. double click...

8 years ago | 0

| accepted

Answered
CCS/F28M36P63C2: Can't compile an auto generated code from Simulink.
Please ensure you have latest version of the hardware support package installed - 17.2.2 This can verified by clicking - Add-On...

8 years ago | 0

Answered
CCS/F28M36P63C2: Can't compile an auto generated code from Simulink.
Hi, Did you try to launch the project from diagnostic viewer from MATLAB. We support automatic project creation in CCS from M...

8 years ago | 0