Answered
How to solve the "No rule to make target `.refresh', needed by `ert_main.o.opt'. Stop." when I use Embeded Coder to build generated C code?
Hi, The error "No rule to make target" is typically thrown by the make/gmake build automation tool because it can't find the in...

1 year ago | 0

Answered
TMS320F28377D Simulink External Mode Error
Hi, I understand you are encountering an “rtiostream timeout” error. One possible cause for this issue could be that the GPIO ...

1 year ago | 0

Answered
Failed to generate binary inputs.
Hi Manas , I understand you are encountering a “Failed to generate all binary outputs” error in MATLAB. This particular error ...

1 year ago | 0

Answered
Failed to generate all binary outputs.
Hi Tarek, I understand you are encountering a “Failed to generate all binary outputs” error in MATLAB. This particular error m...

1 year ago | 0

Answered
How to resolve "Failed to generate all binary outputs" while deploying code on F28335 Microcontroller using Simulink
Hi Muhammad Azeem, I understand you are encountering a “Failed to generate all binary outputs” error in MATLAB. This particula...

1 year ago | 0

Answered
Run Time Error in Texas Instruments C2000 PIL Testing
Hi Sivakumar, I understand you are encountering an “rtiostream timeout” error when trying to run a PIL simulation on a C2000 ta...

1 year ago | 0

Answered
How to use Matlab generated PWM pulse in C2000 epwm block
Hi Pratyay, I understand you want to use a MATLAB-generated PWM pulse in the C2000 ePWM block. You can use the MATLAB-generat...

1 year ago | 0

Answered
Linearize FMU model in Simulink
Hi Alberto, I understand you want to understand if import bock supports linearization of FMU models. FMU import block supports...

1 year ago | 0

Answered
TI C2000 Microcontroller Slow IPC-Transmission of an int32 with just 1kHz
Hi Marcel, I understand you are experiencing performance issues with the IPC transmission. When testing the IPC connection in c...

2 years ago | 0

Answered
Stoping epwm after one period via one-shot trip
Hi, I understand you want to disable the ePWM after a trip event. The Trip Zone settings of the ePWM block can be configured to...

2 years ago | 0

Answered
How to send these ADC values in a buffer over SPI using c2000 blocks
Hi Haadia, I understand that you want to share the ADC data to SPI. You can use the SPI Transmit (or Receive) block to send (o...

2 years ago | 0

Answered
TMS320F28335: how to disable epwm module after a certain time in simulink
Hi, I understand you want to disable the ePWM module. You can use the Trip Zone unit to disable the ePWM. You may select the s...

2 years ago | 0

Answered
Why does the spi block not send the second value?
Hi Haadia, I can understand that you are not able to send complete data through the SPI blocks. Following the steps mentioned b...

2 years ago | 0

Answered
when I use TI C2000 microcontroller blockset demos to generate code for F28069 Launchpad, error reports like these
Hi Bin, I understand you are encountering the error: 'The left-hand side of a . operator must be a valid scope identifier' when...

2 years ago | 0

Answered
cast shadow in Simulink 3D Animation
Hi Simon, I understand you want to cast the shadow of an object onto another surface in Simulink 3D Animation. To achieve this,...

2 years ago | 0

Answered
Error when using MATLAB toolbox for Ryze Tello Drones: Dot indexing is not supported for variables of this type.
Hi kiattisak, I can understand that you are getting the following error: “Dot indexing is not supported for variables of this ...

2 years ago | 0

Answered
Abnormal exit error while running model advisor check
Hi Niraj, I understand you are receiving an unexpected error when running model advisor on your Stateflow model. This appears t...

2 years ago | 0

Answered
Incapable of getting datas from Arduino Mega 2560
Hi Pierre-Olivier, I can understand that you are getting the following error: External Mode Open Protocol Connect command fail...

2 years ago | 0

Answered
Finding the transfer function of a DC-DC Converter and then calculating PI values for controller
Hi Chukwudalu, To understand the Dual Active Bridge converter, you shall refer to the following demo on “Modeling and Control o...

2 years ago | 0

Answered
How to get loan value for fixed time span and payment
Hi Peter, I understand that you want to calculate the remaining loan amount using a built-in function. You mentioned the 'amort...

2 years ago | 0

Answered
How does Model Advisor determine the default configuration ?
Hi Mohamed-Marwan, I understand that you want to run a particular set of checks every time on a model and wish to know how the ...

2 years ago | 0

Answered
Detect if block is part of a feedback loop
Hi Vince, I understand that it can sometimes be confusing to follow the flow of a model, especially when dealing with large and...

2 years ago | 0

Answered
some letters like "c""d" can't display correctly in commandline
Hi, I understand that when the lowercase letters c, d, and o are pressed, they appear as blanks. This issue appears to occur ...

2 years ago | 5

| accepted

Answered
How can I constrain a plot on an excel sheet?
Hi Christian, To ensure your chart remains within a specified area on the Excel worksheet, you can define its position and dime...

2 years ago | 0

Answered
How do I make a contour?
Hi 민제 강, To achieve smoother contours in your plot, you can interpolate the kerr onto a finer grid using interp2. Create a dens...

2 years ago | 0

Answered
Replacement for MFE Toolbox Function normloglik
Hi Tilman, In MATLAB, if you are using the MFE Toolbox and encounter an issue with the function normloglik not being recognized...

2 years ago | 0

Answered
How to do probabilistic forecast in Matlab?
Hi israt, In MATLAB, there are several options for performing probabilistic forecasting, particularly in the context of energy ...

2 years ago | 0

Answered
How can i do Probabilistic time series forecasting?
Hi israt, In MATLAB, probabilistic forecasting can be approached using two primary functions: 'forecast' and 'simulate'. The 'f...

2 years ago | 0

Answered
How to specify a seasonal ARIMA model
Hi Md. Golam, To specify a seasonal ARIMA model with the given parameters you can use the 'arima' function as follows: % Defin...

2 years ago | 0

Answered
How to specify a Seasonal ARIMA model?
Hi Dinuka, To specify a seasonal ARIMA model with the given parameters in MATLAB (R2023a), you can use the 'arima' function as ...

2 years ago | 2