IGBT

Implement insulated gate bipolar transistor (IGBT)

• 

Libraries:
Simscape / Electrical / Specialized Power Systems / Power Electronics

Description

The IGBT block implements a semiconductor device controllable by the gate signal. The IGBT is simulated as a series combination of a resistor Ron, inductor Lon, and a DC voltage source Vf in series with a switch controlled by a logical signal (g > 0 or g = 0).

The IGBT turns on when the collector-emitter voltage is positive and greater than Vf and a positive signal is applied at the gate input (g > 0). It turns off when the collector-emitter voltage is positive and a 0 signal is applied at the gate input (g = 0).

The IGBT device is in the off state when the collector-emitter voltage is negative. Note that many commercial IGBTs do not have the reverse blocking capability. Therefore, they are usually used with an antiparallel diode.

The IGBT block contains a series Rs-Cs snubber circuit, which is connected in parallel with the IGBT device (between terminals C and E).

The turnoff characteristic of the IGBT model is approximated by two segments. When the gate signal falls to 0, the collector current decreases from Imax to 0.1 Imax during the fall time (Tf), and then from 0.1 Imax to 0 during the tail time (Tt).

Examples

The power_igbtconv example illustrates the use of the IGBT block in a boost DC-DC converter. The IGBT is switched on and off at a frequency of 10 kHz to transfer energy from the DC source to the load (RC). The average output voltage (V_R) is a function of the duty cycle (α) of the IGBT switch:

$$V_R=\frac{1}{1-\alpha }{V}_{dc}$$

Assumptions and Limitations

• The IGBT block implements a macro model of the real IGBT device. It does not take into account either the geometry of the device or the complex physical processes [1].

• Depending on the value of the inductance Lon, the IGBT is modeled either as a current source (Lon > 0) or as a variable topology circuit (Lon = 0). The IGBT block cannot be connected in series with an inductor, a current source, or an open circuit, unless its snubber circuit is in use.

• The inductance Lon is forced to 0 if you choose to discretize your circuit.

Ports

Input

g — IGBT control signal

Simulink^® signal

Simulink signal to control the opening and closing of the IGBT.

Output

m — Switch output

Simulink signal

The Simulink output of the block is a vector containing two signals. You can demultiplex these signals by using the Bus Selector block provided in the Simulink library:

Signal	Definition	Units
1	IGBT current	A
2	IGBT voltage	V

Dependencies

To enable this port, select the Show measurement port parameter.

Conserving

C — IGBT collector

specialized electrical

Specialized electrical conserving port associated with the IGBT collector.

E — IGBT emitter

specialized electrical

Specialized electrical conserving port associated with the IGBT emitter.

Parameters

To edit block parameters interactively, use the Property Inspector. From the Simulink Toolstrip, on the Simulation tab, in the Prepare gallery, select Property Inspector.

Resistance Ron — Internal resistance of IGBT

0.001 (default) | nonnegative scalar

Internal resistance of the switch device, in ohms (Ω). The Resistance Ron parameter cannot be set to 0 when the Inductance Lon parameter is set to 0.

Inductance Lon — Internal inductance of IGBT

0 (default) | nonnegative scalar

Internal inductance Lon, in henries (H). The Inductance Lon parameter is normally set to 0 except when the Resistance Ron parameter is set to 0.

Forward voltage Vf — Forward voltage of IGBT

1 (default) | nonnegative scalar

Forward voltage of the IGBT device, in volts.

Initial current Ic — Initial current flowing in IGBT

0 (default) | nonnegative scalar

Initial current flowing in the IGBT. It is usually set to 0 to start the simulation with the device blocked.

If the Initial current Ic parameter is set to a value greater than 0, the steady-state calculation considers the initial status of the IGBT as closed. Initializing all states of a power electronic converter is a complex task. Therefore, this option is useful only with simple circuits.

Snubber resistance Rs — Snubber resistance

1e5 (default) | nonnegative scalar

Snubber resistance, in ohms (Ω). Default is 1e5. Set the Snubber resistance Rs parameter to inf to eliminate the snubber from the model.

Snubber capacitance Cs — Snubber capacitance

inf (default) | nonnegative scalar

Snubber capacitance in farads (F). Default is inf. Set the Snubber capacitance Cs parameter to 0 to eliminate the snubber, or to inf to get a resistive snubber.

Show measurement port — Option to show measurement port

on (default) | off

If selected, add a Simulink output to the block returning the IGBT current and voltage.

References

[1] Mohan, N., T.M. Undeland, and W.P. Robbins, Power Electronics: Converters, Applications, and Design, John Wiley & Sons, Inc., New York, 1995.

Extended Capabilities

C/C++ Code Generation
Generate C and C++ code using Simulink® Coder™.

Version History

Introduced before R2006a