Output Port
Connection block from RF physical blocks to Simulink environment
Libraries:
RF Blockset /
Equivalent Baseband /
Input /
Output Ports
Description
The Output Port block produces the basebandequivalent timedomain response of an input signal traveling through a series of RF physical components. The Output Port block
Partitions the RF physical components into linear and nonlinear subsystems.
Extracts the complex impulse response of the linear subsystem for basebandequivalent modeling of the RF linear system.
Extracts the nonlinear AMAM/AMPM modeling for RF nonlinearity.
The Output Port block also serves as a connecting port from an RF physical part of the model to the Simulink^{®}, or mathematical, part of the model. For more information about how the Output Port block converts the physical modeling environment signals to mathematical Simulink signals, see Convert to and from Simulink Signals.
Note
Some RF blocks require the sample time to perform baseband modeling calculations. To ensure the accuracy of these calculations, the Input Port block, as well as the mathematical RF blocks, compare the input sample time to the sample time you provide in the mask. If they do not match, or if the input sample time is missing because the blocks are not connected, an error message appears.
Parameters
Main Tab
Load impedance(ohms) — Load impedance of RF network
50
(default)  scalar
Load impedance of the RF network described in the physical model to which it connects, specified as scalar in ohms.
Visualization Tab
Source of frequency data — Frequency data source
Derived from
Input Port parameter
(default)  Userspecified
Frequency data source in specified based on one of the following:
When Source of frequency data is
Derived from Input Port parameter
, frequency data source will be derived from the parameters set on the Input Port.When Source of frequency data is
Userspecified
, specify as a vector of frequencies in the Frequency data parameter.
Frequency data (Hz) — Frequency data range
1e9:1e8:3e9
(default)  vector
Frequency data range, specified as a vector in hertz.
Dependencies
To enable this parameter, set
Userspecified
in
Source of amplifier gain.
Reference impedance (ohms) — Reference impedance
50
(default)  scalar
Reference impedance of the coaxial transmission line, specified as a scalar in ohms.
Plot type — Type of data plot
XY
plane
(default)  Composite data
 Polar plane
 Z Smith chart
 Y Smith chart
 ZY Smith chart
Type of data plot that you want to produce with your data specified as:
XY plane
— Generate a Cartesian plot of your data versus frequency. To create linear, semilog, or loglog plots, set the Y scale and X scale accordingly.Composite data
—The composite data plot automatically generates four separate plots in one figure window, showing the frequency dependence of several parameters.Polar plane
— Generate a polar plot of your data. The block plots only the range of data corresponding to the specified frequencies.Z Smith chart
,Y Smith chart
, andZY Smith chart
— Generate a Smith^{®} chart of your data. The block plots only the range of data corresponding to the specified frequencies.
Y parameter1 — Type of parameters to plot
S11
(default)  S12
 S21
 S22
 GroupDelay
 OIP3
 NF
 ...
Type of parameters to plot based on the Plot type you set, specified as one of the following.
Plot type  Y parameter1 

XY plane  S11 ,
S12 ,
S21 ,
S22 ,
Gt ,
GroupDelay ,
GammaIn ,
GammaOut ,
VSWRIn ,
VSWROut ,
OIP3 ,
NF ,
NFactor , and
NTemp . 
Composite data  No Y parameter1 to set. 
Polar
plane  S11 ,
S12 ,
S21 ,
S22 ,
GammaIn , and
GammaOut 
Z Smith chart  S11 ,
S22 ,
GammaIn , and
GammaOut . 
Y Smith chart  S11 ,
S22 ,
GammaIn , and
GammaOut . 
ZY smith
chart  S11 ,
S22 ,
GammaIn , and
GammaOut . 
Y parameter2 — Type of parameters to plot
S11
(default)  S12
 S21
 S22
 GroupDelay
 OIP3
 NF
 ...
Type of parameters to plot based on the Plot type you set, specified as one of the following.
Plot type  Y parameter2 

XY plane  S11 ,
S12 ,
S21 ,
S22 ,
Gt ,
GroupDelay ,
GammaIn ,
GammaOut ,
VSWRIn ,
VSWROut ,
OIP3 ,
NF ,
NFactor , and
NTemp . 
Composite data  No Y parameter2 to set. 
Polar
plane  S11 ,
S12 ,
S21 ,
S22 ,
GammaIn , and
GammaOut 
Z Smith chart  S11 ,
S22 ,
GammaIn , and
GammaOut . 
Y Smith chart  S11 ,
S22 ,
GammaIn , and
GammaOut . 
ZY smith
chart  S11 ,
S22 ,
GammaIn , and
GammaOut . 
Y format1 — Plot format
Magnitude
(decibels)
(default)  Mag
 Magnitude
(linear)
 Angle
 Real
 Imaginary
 ...
Plot format, specified as one of the following.
Y prarameter1  Y format1 

S11 ,
S12 ,
S21 ,
S22 ,
GammaIn , and
GammaOut .  dB ,
Magnitude (decibels) ,
Abs ,
Mag ,
Magnitude (linear) ,
Angle ,
Angle(degrees) ,
Angle(radians) ,
Real ,
Imag , and
Imaginary . 
GroupDelay  ns ,
us ,
ms ,
s , and
ps . 
VSWRIn ,
VSWROut , and
Gt .  Magnitude
(decibels) and
None . 
OIP3  dBm ,
dBW ,
W , and
mW . 
NF

Magnitude
(decibels) . 
NFactor  None 
NTemp  Kelvin 
Dependencies
To enable Y format1,
set Plot type to
XY plane
.
Y format2 — Plot format
Magnitude
(decibels)
(default)  Mag
 Magnitude
(linear)
 Angle
 Real
 Imaginary
 ...
Plot format, specified as one of the following.
Y prarameter2  Y format2 

S11 ,
S12 ,
S21 ,
S22 ,
GammaIn , and
GammaOut .  dB ,
Magnitude (decibels) ,
Abs ,
Mag ,
Magnitude (linear) ,
Angle ,
Angle(degrees) ,
Angle(radians) ,
Real ,
Imag , and
Imaginary . 
GroupDelay  ns ,
us ,
ms ,
s , and
ps . 
VSWRIn ,
VSWROut , and
Gt .  Magnitude
(decibels) and
None . 
OIP3  dBm ,
dBW ,
W , and
mW . 
NF

Magnitude
(decibels) . 
NFactor  None 
NTemp  Kelvin 
Dependencies
To enable Y format2,
set Plot type to
XY plane
.
X parameter — X parameter
Freq
(default)
Parameter, specified as
Freq
. This parameter determines
the data for xaxes on the XY plane plot.
X format — Plot format
Hz
(default)  Auto
 KHz
 MHz
 GHz
 THz
Plot format, specified as one of the following
Hz
, Auto
,
KHz
, MHz
,
GHz
or
THz
.
Y scale — Yaxis scale
Linear
(default)  Log
Yaxis scale, specified as
Linear
or
Log
.
X scale — Xaxis scale
Linear
(default)  Log
Xaxis scale, specified as
Linear
or
Log
.
Plot — Plot specified data
button
Plot the specified data using the plot button.
Dependencies
The Visualization tab shows parameters for creating plots if you display the Output Port mask after you perform one or more of the following actions:
Run a model with two or more blocks between the Input Port block and the Output Port block.
Click the Update Diagram button to initialize a model with two or more blocks between the Input Port block and the Output Port block.
For information about plotting, see Create Plots.
More About
Linear Subsystem
For the linear subsystem, the Output Port block uses the Input Port block parameters and the interpolated Sparameters calculated by each of the cascaded physical blocks to calculate the basebandequivalent impulse response. Specifically, it
Determines the modeling frequencies f as an Nelement vector. The modeling frequencies are a function of the center frequency f_{c}, the sample time t_{s}, and the finite impulse response filter length N, all of which you specify in the Input Port block dialog box.
The nth element of f, f_{n}, is given by
$$\begin{array}{cc}{f}_{n}={f}_{\mathrm{min}}+\frac{n1}{{t}_{s}N}& n=1,\mathrm{...},N\end{array}$$
where
$${f}_{\mathrm{min}}={f}_{c}\frac{1}{2{t}_{s}}$$
Calculates the passband transfer function for the frequency range as
$$H(f)=\frac{{V}_{L}(f)}{{V}_{S}(f)}$$
where V_{S} and V_{L} are the source and load voltages, and f represents the modeling frequencies. More specifically,
$$H(f)=\frac{{S}_{21}\left(1+{\Gamma}_{l}\right)\left(1{\Gamma}_{s}\right)}{2\left(1{S}_{22}{\Gamma}_{l}\right)\left(1{\Gamma}_{in}{\Gamma}_{s}\right)}$$
where
$$\begin{array}{l}{\Gamma}_{l}=\frac{{Z}_{l}{Z}_{o}}{{Z}_{l}+{Z}_{o}}\\ {\Gamma}_{s}=\frac{{Z}_{s}{Z}_{o}}{{Z}_{s}+{Z}_{o}}\\ {\Gamma}_{in}={S}_{11}+\left({S}_{12}{S}_{21}\frac{{\Gamma}_{l}}{\left(1{S}_{22}{\Gamma}_{l}\right)}\right)\end{array}$$
and
Z_{S} is the source impedance.
Z_{L} is the load impedance.
S_{ij} are the Sparameters of a twoport network.
The blockset derives the passband transfer function from the Input Port block parameters as shown in the following figure:
Translates the passband transfer function to baseband as H(f – f_{c}), where f_{c} is the specified center frequency.
The baseband transfer function is shown in the following figure.
Obtains the basebandequivalent impulse response by calculating the inverse FFT of the baseband transfer function. For faster simulation, the block calculates the IFFT using the next power of 2 greater than the specified finite impulse response filter length. Then, it truncates the impulse response to a length equal to the filter length specified.
For the linear subsystem, the Output Port block uses the calculated impulse response as input to the DSP System Toolbox™ Digital Filter Design (DSP System Toolbox) block to determine the output.
Nonlinear Subsystem
The nonlinear subsystem is implemented by AM/AM and AM/PM nonlinear models, as shown in the following figure.
The nonlinearities of AM/AM and AM/PM conversions are extracted from the power data of an amplifier or mixer by the equations
$$\begin{array}{c}A{M}_{out}=\sqrt{{R}_{l}{P}_{out}}\\ P{M}_{out}=\phi \\ A{M}_{in}=\sqrt{{R}_{s}{P}_{in}}\end{array}$$
where AM_{in} is the AM of the input voltage, AM_{out} and PM_{out} are the AM and PM of the output voltage, R_{s} is the source resistance (50 ohms), R_{l} is the load resistance (50 ohms), P_{in} is the input power, P_{out} is the output power, andϕ is the phase shift between the input and output voltage.
Note
You can provide power data via a .amp
file.
See AMP File Data Sections for information
about this format.
The following figure shows the original power data of an amplifier.
This figure shows the extracted AM/AM nonlinear conversion.
Version History
Introduced before R2006a
See Also
MATLAB Command
You clicked a link that corresponds to this MATLAB command:
Run the command by entering it in the MATLAB Command Window. Web browsers do not support MATLAB commands.
Select a Web Site
Choose a web site to get translated content where available and see local events and offers. Based on your location, we recommend that you select: .
You can also select a web site from the following list:
How to Get Best Site Performance
Select the China site (in Chinese or English) for best site performance. Other MathWorks country sites are not optimized for visits from your location.
Americas
 América Latina (Español)
 Canada (English)
 United States (English)
Europe
 Belgium (English)
 Denmark (English)
 Deutschland (Deutsch)
 España (Español)
 Finland (English)
 France (Français)
 Ireland (English)
 Italia (Italiano)
 Luxembourg (English)
 Netherlands (English)
 Norway (English)
 Österreich (Deutsch)
 Portugal (English)
 Sweden (English)
 Switzerland
 United Kingdom (English)