Double-acting cylinder operated by hydraulic and pneumatic power
The Pneumo-Hydraulic Actuator block simulates a pneumo-hydraulic actuator, implemented as a double-acting cylinder with one side connected to a hydraulic power supply and another side operated by pneumatic power. Such devices are widely used as pneumo-hydraulic pumps, intensifiers, and converters of various types. The following illustration shows a few examples of the pneumo-hydralic actuator: a) with rigid separator; b) with flexible separator; c) pneumo-hydraulic intensifier.
The hydraulic part of the model accounts only for fluid consumption associated with the piston velocity. The pneumatic part of the model is built with the ideal gas relationships. To simulate the limit on the piston motion, the hard stop is included in the model. The piston effective area is assumed to be constant. As a result, the model is described with the following equations:
|qH||Hydraulic volumetric flow rate|
|p||Pressure in the actuator chambers|
|AH||Hydraulic side effective area|
|AP||Pneumatic side effective area|
|FH||Force developed by piston on hydraulic side|
|FP||Force developed by piston on pneumatic side|
|FHS||Hard stop force|
|FL||Force developed by external load connected to port L|
|K||Hard stop stiffness|
|D||Hard stop damping|
|VP||Chamber volume on pneumatic side|
|V0||Chamber dead volume on pneumatic side|
|G||Gas mass flow rate|
|T||Gas absolute temperature|
|QP||Heat flow through the pneumatic chamber|
|cv||Gas specific heat at constant volume|
|cp||Gas specific heat at constant pressure|
|QHE||Heat flow through the thermal port E|
The model is suitable for building pneumo-hydraulic or hydro-pneumatic pumps, intensifiers, and similar devices. You can simulate piston loading (such as inertia, springs, friction) by modeling the load externally and connecting it to port L. Similarly, simulate the heat exchange with the environment through the external thermal port E, which corresponds to the gas in the chamber. Use blocks from the Simscape™ Foundation library, such as the Convective Heat Transfer, Conductive Heat Transfer, Thermal Mass, and so on, depending on the actual system configuration.
Port P is the pneumatic conserving port associated with the pneumatic side of the actuator. Port H is the hydraulic conserving port associated with the hydraulic inlet.
The block directionality assumes that pressure in the hydraulic chamber causes the piston to move in the positive direction, while pressure in the pneumatic chamber tends to move the piston in the negative direction. Flow rates are considered positive if they flow into the actuator.
The effective piston area in each chamber is assumed to be constant.
The leakage flow between chambers is assumed to be negligible because pressures in the chambers are equal.
On the hydraulic side, fluid compressibility is not taken into account.
On the pneumatic side, the mass flow rate and heat flow computations assume that the gas is ideal.
Effective piston area on the hydraulic side. The default value
Effective piston area on the pneumatic side. The default value
Piston maximum travel between caps. The default value is
The distance between the piston and the cap on the hydraulic
side at the beginning of simulation. This value cannot exceed the
piston stroke. The default value is
Chamber dead volume on the pneumatic side. The default value
The hard stop model implemented in the block assumes that the
stop resists penetration of the piston with force proportional to
the penetration. This parameter sets the stiffness of the contact
between the stop and the piston. The default value is
The damping in the hard stop model accounts for dissipation
in the piston-stop contact. The default value is
The initial absolute pressure in the pneumatic chamber. The
default value is
The initial gas temperature in the pneumatic chamber. The default
The block has the following ports:
Hydraulic conserving port associated with the actuator hydraulic chamber.
Pneumatic conserving port associated with the actuator pneumatic chamber.
Mechanical translational conserving port associated with the actuator piston. You can model the load on the piston, such as external force, inertia, friction, or spring, and connect it through this port.
Thermal conserving port associated with the gas in the pneumatic chamber. You can simulate the heat exchange with the environment through this port.